HOME> 在线世界杯> iPhone 15 Screen Replacement

iPhone 15 Screen Replacement

2025-12-03 13:31:52

步骤 27

Remove the screen adhesive

Be careful not to damage any of the spring contacts as you clean the frame.

This is a good point to test your repair before sealing up your phone. Connect the screen, power on your phone, and make sure it works as expected. Power it back down and continue reassembly.

The adhesive remaining on your phone is difficult to remove and leaves residue. If you have trouble removing the adhesive, apply some heat using a hair dryer or heat gun.

Use a spudger to push the screen adhesive up until you can grab it with a pair of tweezers.

Use a pair of tweezers, or your fingers, to remove the adhesive around the entire perimeter of the iPhone.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 28

Any leftover residue will compromise your iPhone's seal. Be sure to clean the frame thoroughly.

Wrap a microfiber or lint-free cloth around the pointed end of a spudger and apply a few drops of high-concentration (greater than 90%) isopropyl alcohol to the cloth.

Wipe in one direction along the perimeter of the frame to clean the adhesive residue.

Wait a few minutes before proceeding to make sure any excess alcohol has evaporated.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 29

Ambient light sensor information

The ambient light sensor is located behind the screen, directly beneath the cut‑out for the Face ID sensors.

Check if the replacement screen comes with one installed. If it does, skip to this step.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 30

Remove the ambient light sensor bracket

Use a Phillips screwdriver to remove the 1.3 mm‑long screw securing the ambient light sensor bracket.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 31

Use a pair of tweezers or your fingers to lift and remove the ambient light sensor bracket.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 32

Heat the ambient light sensor

Use a hair dryer, heat gun, or heated iOpener to soften the adhesive under the ambient light sensor and ambient light sensor cable.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 33

Pry up the ambient light sensor

Use a spudger to pry up the ambient light sensor.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 34

Peel up the ambient light sensor cable

Gently slide an opening pick under the ambient light sensor cable, starting near the sensor and moving towards to the opposite corner until it's free from the screen.

If the adhesive doesn't peel up easily, apply more heat.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 35

Remove the ambient light sensor

Use a pair of tweezers to lift the ambient light sensor off of the screen.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 36

Prepare the ambient light sensor

在这个步骤中使用的工具：

Tesa 61395 Tape

$2.99

购买

Use tweezers to reposition any adhesive that may have covered the ambient light sensor during removal. The adhesive should form a border around the raised white rectangle.

If the adhesive was damaged or stayed with the old screen, replace it with a 1 mm wide strip of thin, double-sided tape along its bottom border.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 37

Place the ambient light sensor

Align the ambient light sensor with its recess in the back of the screen.

Use a spudger or your finger to press the ambient light sensor into its recess.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 38

Warm the ambient light sensor

Use a hair dryer, heat gun, or heated iOpener to soften the adhesive under the ambient light sensor and ambient light sensor cable. It only needs to be warm—not hot.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 39

Press the ambient light sensor

在这个步骤中使用的工具：

Tesa 61395 Tape

$2.99

购买

Use your finger to press down the ambient light sensor cable.

If the ambient light sensor cable isn't sticking, apply a few small pieces of double‑sided tape, like Tesa tape, to the back of the sensor cable.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 40

Install the ambient light sensor bracket

Use tweezers or your fingers to hook the ambient light sensor bracket over the back of the sensor and set it into place.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 41

Use a Phillips screwdriver to install the 1.3 mm‑long screw securing the ambient light sensor bracket.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 42

Orient the adhesive

Lay the adhesive next to the phone and use features like cutouts for spring contacts and the front‑facing camera to make sure the adhesive is oriented correctly.

Your adhesive may look slightly different.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 43

Apply the adhesive

Once the adhesive is pressed into place, you can't reposition it—you'll have to remove it and start over with new adhesive.

Use the pull tab to begin peeling the back liner off of the adhesive starting from the bottom, but do not remove the liner all the way.

While holding the back liner out of the way, carefully align the exposed edge of the adhesive to the bottom edge of the iPhone's frame.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 44

When the adhesive is aligned, use the flat end of a spudger, or your finger, to press it down firmly along the bottom edge.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 45

Continue peeling the back liner off of the adhesive while pressing the adhesive into place along the edges of the iPhone's frame.

If you correctly aligned the lower edge of the adhesive, the side and top edges will fall perfectly into place. If the adhesive is misaligned, remove it and start over with new adhesive.

If your adhesive is misaligned and you don't have another set handy, it's okay to temporarily put your iPhone back together and use it normally without any adhesive, but keep in mind that your iPhone's water resistance will be compromised until you install new adhesive.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 46

Press the adhesive into place

Make sure the liner is aligned properly by checking that all spring contacts and the front-facing camera are in their cutouts. If they aren't, remove the adhesive and start over with a new sheet.

Use the flat end of a spudger to press the adhesive firmly into place all around the iPhone.

Be careful not to press on the camera, spring contacts, or other internal components.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 47

Remove the top liner

Insert the point of a spudger under the top liner's hole at the bottom of the frame.

Pry up to separate the liner from the frame—enough to grip it with your fingers.

Your pull tab may be in a different location. Make sure you're pulling the full-size top liner, not the thin liners under it.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 48

Peel back the top liner and remove it.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 49

Prop up the screen

Prop the screen up along the left edge of the iPhone frame, using a box or similar sturdy object to support the screen.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 50

Connect the screen

Use the flat end of a spudger or your finger to connect the screen and front sensor press connectors.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 51

Insert the top of the screen connector cover into its slot in the frame and lay it over the press connector.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 52

Insert the front sensor connector cover into its slot in the frame at a 90‑degree angle vertically.

Lay the cover over the press connector.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 53

Install the cover screws

Use a tri-point Y000 driver to install the two 0.9 mm‑long screws securing the front sensor connector and screen connector covers.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 54

Remove the final adhesive liners

As you remove the liners in this step, the adhesive will be fully exposed. Make sure nothing touches the exposed adhesive.

Use a spudger, or your fingers, to separate the pull tabs at the bottom right corner of the frame.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 55

Remove the narrow liner covering the adhesive along the right and top edges of the frame.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 56

Remove the liner along the bottom edge of the frame.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 57

Without letting the screen touch the adhesive, hold the screen over the phone so you can access the final liner along the left edge of the phone.

Use a pair of tweezers or your fingers to remove the final liner along the left edge of the phone.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 58

Place the screen

Lay the screen straight down onto the frame and press until the clips engage.

Press around the perimeter of the screen to engage all clips.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 59

Heat the screen

To help the adhesive bond, apply heat to the edges of the screen using an iOpener, hair dryer, or heat gun until it's hot to the touch.

If you have screen vise clamps, use them to strengthen the bond of your new adhesive. If not, keep reading for more ways to secure the screen.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 60

Press the screen

To evenly compress your iPhone and strengthen the bond of the screen to the frame, you need to account for the camera bump.

If you have the box your iPhone came in, take the lid and place it on a flat surface.

If you don't have your original box, skip this step for an alternate method.

Place your iPhone screen-side-up in the lid of your box with the camera bump in its recess.

Find something close to the size of your iPhone, but taller than the sides of the box. Stack it on top of the iPhone, followed by a few heavy objects.

Leave the objects in place for at least thirty minutes. The lighter the objects, the longer they should be left. Ideally, leave them stacked overnight.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 61

If you don't have the original box for your iPhone, follow the next three steps for another method to evenly compress the screen.

Place the iPhone screen-side-down on a soft, flat surface.

Apply tape to the back glass to protect its finish.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 62

Place evenly spaced layers of coins or similarly thick objects on the tape along the edges of the back glass.

Stack them to a consistent height taller than the camera bump.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

步骤 63

Stack multiple books or other heavy objects on your iPhone.

The coins may leave an impression on the bottom object, so don't use anything valuable.

Leave the objects in place for at least thirty minutes. The lighter the objects, the longer they should be left. Ideally, leave them stacked overnight.

翻译

添加一条评论

添加评论

1024

取消

发帖评论

魔灵召唤仙人各属性详解
独步天下